fbpx
Jump to Forum..

Determination of rpm @ certain power settings

in 912 / 914 Technical Questions 8 years ago
Hello,

Goodevening.
Could not find a reference regarding the determination of a rpm @ certain power setting. For instance: what is the rpm at 75% power setting. For a ROTAX912S the rpm=5000 @ 75% power setting.

Best regards Jan

  • Re: Determination of rpm @ certain power settings

    by » 8 years ago

    Are you looking for a chart with all the percentages and rims?
    The answer is predicated on your prop pitch. If you are over or under pitched the rpm vs % of power will be different. I believe the manual takes into account that you can achieve 5800 rpm. For instance; Most of us don't get 5800 with a ground adjustable prop. What type of prop setup do you have? In flight adjustable or ground adjustable?

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: Determination of rpm @ certain power settings

    by » 8 years ago

    I have a ground adjustable prop: DUC Swirl.

    The following article gives the answer:
    How To Determine The Part-Throttle RPM of a Fixed Pitch Propellor At a Given Horsepower by Stan Hall, EAA.
    He has determined the following table:
    Power Setting 75% Multiplier=0,91
    Power Setting 65% Multiplier=0,87

    First you have to determine your WOT level flight RPM: RPM1 then your RPM @given Power Setting is RPM2=RPM1*Multiplier!

    Example at 75% Power Setting:
    Suppose @WOT level flight we obtain RPM1=5800 RPM then RPM2=5800*0,91=5278RPM.
    RPM1 depends as Roger said on over or under pitching and at what cruise level we fly.
      
    Report

  • Re: Determination of rpm @ certain power settings

    by » 8 years ago

    That is just the textbook "Power vs.Velocity" Formula.
    Velocity is proportional to the Cube Root of the Power.

    The cube root of 75% is 91%
    The cube root of 65% is 87%
    The cube root of 50% is 79%

    This works reasonably well within a few hundred feet above Sea level but way off at altitude.
    At 8000ft 75% Sea level Power is closer to 97% Max rpm.

    RPM x MAD (Manifold Air Density) will be real close throughout the range.

    Bill Hertzel
    Rotax 912is
    North Ridgeville, OH, USA
    Clicking the "Thank You" is Always Appreciated by Everyone.

      
    Report

  • Re: Determination of rpm @ certain power settings

    by » 8 years ago

    Are you looking for a chart with all the percentages and rims?
    The answer is predicated on your prop pitch. If you are over or under pitched the rpm vs % of power will be different. I believe the manual takes into account that you can achieve 5800 rpm. For instance; Most of us don't get 5800 with a ground adjustable prop. What type of prop setup do you have? In flight adjustable or ground adjustable?


    Hi Roger,

    Can I just clarify this a little more. I am new to the 912 having upgraded from a 582 and so am trying to build a picture of how mine should be performing.
    You say that with a ground adjustable prop most do not get 5800RPM and I would guess that is at the standard ops manual prop setting?

    I am running a 912UL on an Airborne XT Trike with a Bolly ground adjustable prop. If I set my prop pitch as per the maint manual I am lucky to get around 5000-5200 when I go full throttle on the runway. By going 3deg fine on the props I can get that to 5500 under the same conditions (my airfield is sea level).

    I considered something wrong due to this and interestingly in comparing with another machine very similar to mine with prop set to the maint manual this one actual indicates 5800 on the runway!

    I am sure this subject has been laboured a bit but perhaps you could offer some additional comments based on the above?

    Cheers Roger
    Craig
      
    Report

  • Re: Determination of rpm @ certain power settings

    by » 8 years ago

    Hi Craig,

    Just to summarize Roger above and beyond.

    At ground level you should get around max 5000-5200 RPM.

    At WOT (Wide Open Throttle) at cruising altitude you should get around 5800 RPM. You have to check this.

    Cruising at 75% is then around 5200 RPM.

    Cheers
      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
Fuel Pressure Alarm Settings 912iS Technical Questions 0
Sudden drop in RPM while changing fuel tank 912iS Technical Questions 3
Rotax 582 not smooth at all power settings 2 Stroke Technical Questions 3
RPM 914turbo 912 / 914 Technical Questions 3
at which rpm needle jet begin to raise? what are signs of clogged bypass holes? 912 / 914 Technical Questions 2

info@rotax-owner.com