fbpx
Jump to Forum..

TRAINING ON ROTAX 582&912

in General Tech Discussion 13 years ago
Hi every one
i am an LSA pilot and power parachut instructor and i would like to go throu a deep cource for ROTAX 582 and 912 engines.
so can any one recomend a good training center any where .
regards

  • Re: TRAINING ON ROTAX 582&912

    by » 13 years ago

    Hi Awod,

    Where do you live? There are several places to get a class on the Rotax engine, but they are regional setups.

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: TRAINING ON ROTAX 582&912

    by » 13 years ago

    Hi again
    Thank you for your quick replay , i am from saudia arabia and i am orignaly aircraft elecrtonic technition for the big C130 aircrafts .
    And i am trying to be the techintion on my reagon for the rotax engines because there is alotof pilots using this kind of engines.
    Thanks again
      
    Report

  • Re: TRAINING ON ROTAX 582&912

    by » 13 years ago

    Hi Awod,

    I don't think there is anything in your country. You may have to travel to Africa or Europe. I'm not sure and it would be best for you to look up Rotax on the web and try to find the closest place through them. The Rotax Flying and Safety club has many places listed, but nothing close and I'm not sure if it is 100% up to date.

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: TRAINING ON ROTAX 582&912

    by » 13 years ago

    THANK YOU VERY MUCH FOR YOU RWEPLAY .
    YES YOU ARE RIGHT THERE IS NOTHING HERE IN MT REAGON.
    I BREFERE TO GO TO USA I THINK THERE IS ALOT OF TRAINING CENTERS.

    BEST WESHIS AND MEREY CRISEMES ;)
      
    Report

  • Re: TRAINING ON ROTAX 582&912

    by » 13 years ago

    Hi Awod

    The best School bar none is the boys up in Canada at Rotech Flight Safety, see: www.RotechFlightSafety.com

    They specialize in training on all series Rotax engines, were the founders of the iRMT programs advising the Rotax factory on same and do training for other Rotax Distributors from all parts of the world as well as for the Rotax factory itself. I've attended their courses and they are second to no one. If you check out their web site you will see their course schedules and prices.

    When I took my courses with them they had students from all parts of the world, and their location in Vernon B.C., Canada is easy to get to flying from Seattle Washington, Vancouver B.C. or Calgary Alberta to Kelowna B.C. Canada. Vernon is only a short drive North of Kelowna(the International Airport you would fly into). All this information is on their web site.

    If you want the best training possible these are the guys to go to and the prices are in line with any other course offerings I've seen!

    Good luck.........Ralph
      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
Rotax 912iS Regulator B w/ Grey Connector Parts 0
rotax rick 618 overhaul 2 Stroke Technical Questions 3
Rotax 582 not smooth at all power settings 2 Stroke Technical Questions 3
Rotax 912iS 2 Sport 912iS Technical Questions 5
ROTAX Service Instruction: Introduction of Sodium-Filled Exhaust Valves and New Cylinder Heads for ROTAX® Aircraft Engine Types 912 and 912 i (Series) General Tech Discussion 9

info@rotax-owner.com